

อุตสาหกรรมการฉีดขึ้นรูปเป็นหนึ่งในอุตสาหกรรมหลักของอุตสาหกรรมเบา โดยแทรกซึมเข้าสู่ทุกด้านของชีวิต เนื่องจากเป็นอุปกรณ์หลักในการผลิตการฉีดขึ้นรูป เครื่องฉีดขึ้นรูปจึงอยู่ร่วมกับเกรดสูง กลาง และต่ำ โดยมีประเภทต่างๆ มากมายและประเภทการใช้งานที่ไม่มีที่สิ้นสุด แม้แต่ผู้เชี่ยวชาญจำนวนมากในอุตสาหกรรมการประมวลผลการฉีดขึ้นรูปก็ยังรู้สึกทึ่งและยากที่จะเลือกเครื่องฉีดขึ้นรูปที่เหมาะกับความต้องการของตนเอง บุคลากรด้านวิศวกรรมและเทคนิคจำนวนมากของผู้ผลิตเครื่องฉีดขึ้นรูปจะรวบรวมเอกสารอ้างอิงบางส่วนเกี่ยวกับวิธีการเลือกเครื่องฉีดขึ้นรูป ซึ่งใช้เมื่อผู้ผลิตอุปกรณ์เลือก อย่างไรก็ตาม วิธีการเลือกเครื่องฉีดขึ้นรูปที่เกี่ยวข้องกับวัสดุเหล่านี้โดยทั่วไปมักจะลำเอียงเกินไป โดยเน้นที่การแนะนำการติดตั้งแม่พิมพ์ ปริมาณการฉีด และการตรวจสอบแรงยึด เป็นต้น ซึ่งเทียบเท่ากับคู่มือที่เขียนโดยผู้ผลิตโทรศัพท์มือถือ ซึ่งบอกคุณว่าโทรศัพท์มือถือนี้สามารถโทรและส่งข้อความได้ ข้อมูล ท่องอินเทอร์เน็ตและฟังเพลงและฟังก์ชั่นอื่น ๆ แต่ไม่ได้บอกคุณว่าเหตุใดโทรศัพท์มือถือรุ่นนี้จึงเปรียบเทียบกับโทรศัพท์มือถืออื่น ๆ สกรูและบาร์เรลตัวเดียวทำไมความเร็วอินเทอร์เน็ตจึงไม่เร็วเท่าโทรศัพท์มือถืออื่น ๆ และทำไมคุณภาพเสียงจึงดีกว่าหรือแย่กว่า ฯลฯ สิ่งเดียวกันนี้ใช้ได้กับเครื่องฉีดพลาสติก เครื่องฉีดพลาสติกบางเครื่องมีตำแหน่งการฉีดที่แม่นยำถึง 0.02 มม. และเครื่องฉีดพลาสติกบางเครื่องมีความผันผวนภายใน 2 มม. เหตุผลสำหรับความแตกต่างนี้ไม่ได้เขียนโดยช่างเทคนิคของผู้ผลิตเครื่องฉีดพลาสติก
Basically, the introductions we have seen in the selection of injection molding machines in the past all require the injection molding machine to “sufficient injection volume, place the mold down, lock tightly, and fully shoot.” In fact, the workshop technicians of the injection molding machine manufacturer know it. These rules, but sometimes the technicians just don’t understand why this machine is better than the other machine next to it, and why the process parameters of this machine can’t be used at all on another machine of the same model.How can a technician distinguish the quality of an injection molding machine? Here is a simple way to verify the repeatability of an injection molding machine.When setting injection parameters, set injection holding pressure, speed, and time to O. When injecting products, first shoot the gate according to the normal parameter settings, then accelerate to the first stage, and then fill to 90-95% of the product full of glue., To ensure that the product lacks a corner state, use the position injection method to shoot the glue, and ensure that the time of each injection is completely the same during the injection molding process (inconsistency indicates that the adjusted parameters are problematic, and the parameters cannot be guaranteed to be executed according to their own adjustment). If there is no change in temperature, repeatedly manufacture N pieces of products, weigh N pieces of trialproduced pieces, and draw the product weight change diagram, and you can see the product weight change circuit diagram. When the average weight deviation between the product and the N products exceeds 0.3%, then The stability of the machine is poor, exceeding 0.5%. The editor recommends that the machine be overhauled.